Rdxfbgrtj

Leyland Lynx
Halton Transport Leyland Lynx in Liverpool
Overview
Manufacturer	Leyland
Production	1986–1992
Assembly	Workington, England
Body and chassis
Doors	1 or 2
Floor type	Step entrance
Powertrain
Engine	Leyland TL11 Gardner 6HLXCT Cummins L10 Volvo THD102KF
Capacity	29 to 52 seated
Transmission	Leyland Hydracyclic semi-automatic ZF Ecomat automatic
Dimensions
Length	11.0 or 12.0 metres
Width	2.5 metres
Height	3.2 metres
Chronology
Predecessor	Leyland National
Successor	Volvo B10B

The Leyland Lynx was a stepped-entrance single-decker bus manufactured by Leyland in Workington, England between 1986 and 1992. After the takeover by Volvo, it was succeeded by the Volvo B10B.

Background

Cardiff Bus Leyland Lynx at Cardiff Central bus station in June 2002

Preston Bus Leyland Lynx during a heritage event in Morecambe in May 2013

Rear of three First Eastern Counties Lynxes in March 2003

The Leyland Lynx (B60) was designed in 1984 as a replacement for the ageing Leyland National, being unveiled at the 1985 International Bus & Coach Exhibition at the Earls Court Exhibition Centre.^[1][2] Although the B60 was the first bus to carry the Lynx brand, Leyland had previously used it on truck chassis between 1936 and 1940, and again between 1968 and 1979.^[3][4] The Lynx name has since been revived by Ashok Leyland for use on a midibus.^[5]

History

Production vehicles began to enter service in 1986, the majority were bodied by Leyland at its Workington factory where the underframe was produced. All have a step entrance, Leyland offered the option of a floor with a step in the middle or one that gently ramped from aft of the front platform to the rear. A plan for offering this bus with a single-piece flat windscreen was considred, but was not carried out. A common feature, therefore, is that the Lynx has two separate windscreens and has the driver's windscreen raked back, resembling 1950s single-decker buses and the Wright Handybus.

Engines offered were the Leyland TL11, Gardner 6HLXCT and Cummins L10, while the Lynx II was also available with the Volvo THD102KF.^[6]

In 1990, the updated Lynx Mark II version was introduced. It could be recognised easily by its protruding front dash/grille panel, whilst the original design was flat. Additionally, a select few of the 140 vehicles produced featured Volvo engines, which drastically reduced performance in pursuit of more environmentally friendly engines.^[7][8]

The Mark II was also available as a bus underframe for other coachbuilders to body.^[8][9] Although the large majority of Lynxes carried the Leyland body, seven chassis were bodied by Alexander with N-type bodywork for Citybus (Belfast), including the first prototype. Northern Counties also catalogued bodies for the Lynx but none were built.^[10][11]

The type saw service all over the United Kingdom, with the largest fleet owned by West Midlands Travel. A total of 256 were purchased, including six demonstrators, delivered early in 1986 equipped with Gardner engines and semi-automatic Leyland Hydracyclic gearboxes (which were later converted to ZF automatic).^[12][13] They were gradually withdrawn from 2000 onwards, with the last three withdrawn from passenger service in March 2009, although 10 remained in the driver training fleet until March 2010.

The last two Lynxes to roll off the production line entered service with Halton Transport in August 1992.^[14] The Lynx was the core of Halton Transport's fleet for over 10 years. In later life at Halton, they were used on a number of school contracts and the occasional regular service.^[15] In October 2010, all of Halton's remaining Lynxes were sold, the last Lynx produced going into preservation, with the penultimate Lynx used to donate spares.

Following the takeover of Leyland by Volvo in March 1988, the Lynx was superseded by the Volvo B10B in 1992.^[16][17] Total production of Lynxes was approximately 1,060 vehicles, including six prototypes (one of which was not bodied) and several development vehicles. About 140 of the total were Lynx Mark IIs.^[18][19]

Exports

A small number of Lynxes were exported as demonstrators, but no sales ever resulted.

In 1984, a framed chassis was sent to Australia. After being completed by JW Bolton in Perth, it operated for Transperth, ACTION and Hornibrook Bus Lines before being sold to Lever Coachlines in 1987.^[20][21] In 1989, two were bodied by Pressed Metal Corporation as demonstrators for the State Transit Authority, but the trial never occurred and they were sold to John J Hill, Wollongong.^[22]

In 1988, Singapore Bus Service took delivery of an Alexander PS type bodied Leyland Lynx. It was involved in an accident in August 2001 and scrapped.^[23] Conversely one Leyland Tiger received a Lynx-style Leyland body for export to New Zealand, initially being operated by Newmans Coach Lines and later Go Bus Transport.^[24]

In 1990, three of the order being built for West Midlands Travel were sent to Australia as demonstrators.^[25] Two operated with ACTION, while the third was demonstrated to the State Transport Authority and State Transit Authority, before all three were sold to Southtrans.^[26][27]

Preservation

Several Lynxes have now entered preservation, with some requiring extensive rebuilding to bring them back to original condition, due to body corrosion, as well as reversing modifications made by operators during their history. One such example is the removal of all of the patterned body skirts, combined with the replacement of the square wheel arches with non-patterned round ones. Both of these modifications were made to make it easier to replace such parts in the event of an accident.

In Australia, the JW Bolton bodied demonstrator has been preserved by the Sydney Bus Museum.^[20][28]

References

External links

Media related to Leyland Lynx at Wikimedia Commons